EdgeLink100 T1/E1 - Telco Systems, a BATM company

Description Documentation Software

EdgeLink100 is the industry's smallest, most cost-effective DS3 multiplexer available. Its compact, plug-and-play architecture enables service providers to turn up T1s and/or E1s fast, saving installation time and costs as well as valuable real estate. Deployed at every edge of the network from the core to the CPE Edge.

Cuts service deployment costs

Compact – only 1 RU – saves valuable real estate
Plug-and-play architecture – fast and easy to install
Remotely manageable
TFTP Software Downloadable – in-service upgrades
Redundant architecture – 1:1

Data Sheets
- EL100 T1/E1 Data Sheet (656.3 KB)

Installation Guides
- EdgeLink100 T1/E1 Installation Guide (895.22 KB)

User Guides
- Non Trouble Procedures (95.34 KB)
  - Acceptance Unit-Level Test (NTP-1) (96.43 KB)
  - Acceptance End-to-End System Level Test (NTP-2) (18.09 KB)
- Trouble Analysis Procedures (178.13 KB)
  - Clear Configuration Mismatch Alarm (TAP-8) (25 KB)
  - Clear DS-1 Trouble (TAP-3) (21.92 KB)
  - Clear DS-3 Trouble (TAP-4) (22.64 KB)
  - Clear Power Supply Trouble (TAP-5) (20.71 KB)
  - Clear Too Many Switches (TMS) Alarm (TAP-7) (23.39 KB)
  - Isolate and Clear an Ambiguous Failure Condition (TAP-6) (16.45 KB)
  - Replace Defective CCA525 (48 Volt) or CCA527 (24 Volt) M13 Card (TAP-2) (88.86 KB)
  - Upgrade EL100 from CCA420 (T1) M13 cards to CCA525 (T1/E1) M13 Cards (TAP-1) (27.14 KB)
- Maintenance and Detailed Level Procedures (822.4 KB)
  - Index of Maintenance and Detailed Level Procedures (DLPs) (108.54 KB)
  - Connect T1/E1 Low-Speed Signal Interface Cables (DLP-507) (160.68 KB)
  - Configure DS3 Interface (DLP-505) (19.15 KB)
  - Configure T1/E1 Interface (DLP-506) (129.13 KB)
  - Configure T1/E1 Line Code (DLP-503) (15.83 KB)
  - Configure T1 Line Buildouts (DLP-504) (16.87 KB)
  - Set T1/E1 Channels to EQUIPPED, UNEQUIPPED, or DISABLED (DLP-500) (17.63 KB)
  - Enable or Disable T1/E1 Auto-Sense or Perform Rescan (DLP-511) (18.58 KB)
  - Set T1/E1 Channels or DS3 Interface to IN-SERVICE (DLP-509) (11.9 KB)
  - Set T1/E1 Channels or DS3 Interface to OUT-OF-SERVICE (DLP-510) (11.82 KB)
  - Initiate a Telnet/SNMP Session (DLP-508) (36.94 KB)
  - Add SNMP Management Capabilites (DLP-502) (15.25 KB)
  - Set M13 card to Factory Default settings (DLP-501) (50.2 KB)
  - Replacing a Side-Mounted Fan Assembly (DLP-527) (120.79 KB)
  - Upgrading to new Front Fan Assembly (DLP-526) (286.29 KB)
- Configuration and Reference Guides (3.07 MB)
  - Craft Port and Telnet (2.15 MB)
  - Ethernet TCP/IP Communications (51.17 KB)
  - SNMP Theory of Operation (444.57 KB)
  - TL1 Theory of Operation (695.06 KB)
  - Unit Configuration, Plug-In, and Cable Compatibility (599.83 KB)
- Specifications (93.92 KB)
- General Description (731.25 KB)
- EdgeLink100 T1/E1 User Guide (6.33 MB)

4.5
- 4.5 Release Notes (33.29 KB)
- 4.5 Software (2.32 MB)
- 4.5 MIB (7.33 KB)
- 4.5 Download Steps (428.97 KB)

4.3
- 4.3 Release Notes (141.92 KB)
- 4.3 Software (2.38 MB)
- 4.3 MIB (7.33 KB)
- 4.3 Download Steps (428.97 KB)

4.4
- 4.4 Release Notes (26.97 KB)
- 4.4 Software (2.27 MB)
- 4.4 MIB (7.33 KB)
- 4.4 Download Steps (428.97 KB)

TFTP Server
- TFTP Server (444.29 KB)